Bambu Lab H2C in SimplyPrint: what works today
Bambu Lab H2C in SimplyPrint: what works today
The Bambu Lab H2C and H2C Combo connect to SimplyPrint through the SimplyPrint Client, like every other Bambu Lab printer. This guide covers how to connect it, what you can do with it, and how the left and right nozzles work in the Cloud Slicer.
In this guide
- Connect your H2C
- What works on the H2C
- Slice for the left or right nozzle
- The nozzle rack
- Related articles
Connect your H2C
Use LAN-only mode. On Bambu Lab firmware from 2025 on, cloud mode only lets SimplyPrint watch the printer: you cannot start prints or control it.- On the printer, turn on LAN-only mode and Developer Mode.
- In the SimplyPrint Client, choose Add printer > Bambu Lab.
- Pick the H2C from the list the Client finds, or enter its IP address.
- Enter the access code and the serial number shown on the printer's screen.
- Enter the setup code the Client shows in SimplyPrint.
Check: the printer shows as online in SimplyPrint, with two nozzles: Nozzle 1 is the left nozzle and Nozzle 2 the right.
What works on the H2C
In LAN-only mode, SimplyPrint can:
- Show live status, time left, layer progress, temperatures and the camera, with AI failure detection.
- Start, pause, resume and cancel prints, and skip objects.
- Print sliced 3MF files (.gcode.3mf), from the Cloud Slicer or from Bambu Studio.
- Map filaments to AMS slots when you start a print, and sync the loaded filament from the AMS.
- Change temperatures, print speed and fans, move and home the printer, extrude, send G-code and change filament.
- Run the print queue with AutoPrint (Pro plan and up).
Bed leveling, Z-offset calibration and baby stepping are not available from SimplyPrint on the H2C.
Slice for the left or right nozzle
The H2C's two nozzles sit side by side, so a file is sliced for a specific nozzle. Each filament in the file is set to the left or the right nozzle.
- Open the file in the Cloud Slicer, select your H2C and use the Bambu Studio or OrcaSlicer engine.
- In the Filaments section, add each filament to the column of the nozzle it is loaded on, Left nozzle or Right nozzle: click + at the top of the column, or drag a filament card into the other column. The columns show while the nozzle assignment mode is Manual, the default.
- Slice, then start the print.
Check: before you slice, each filament card sits in the column of the nozzle it is loaded on. The full walkthrough is in Choosing the left or right nozzle on a Bambu Lab H2D or H2C.
If a print will not use the nozzle you expect, the file was sliced for the other one. Re-slice it with each filament set to the nozzle it is loaded on.
The nozzle rack
The H2C's right extruder has a rack of swappable nozzles. SimplyPrint does not support the nozzle rack yet:
- SimplyPrint shows the H2C as two nozzles, left and right, not the nozzles in the rack.
- The Cloud Slicer slices the H2C the same way, so it cannot slice for a specific nozzle in the rack.
- When SimplyPrint starts a print, it tells the printer which AMS slot each filament comes from, but not which rack nozzle to use. Starting a file that uses rack nozzles from SimplyPrint is not supported.
Print files that only use the left and right nozzles. You can follow H2C progress, and vote for it, on the suggestion board.
Related articles
- Bambu Lab LAN-only mode and Developer Mode: how to enable
- Bambu Lab integration: LAN-only vs Bambu Cloud
- Connect your printers with the SimplyPrint Client
- Multi-color and multi-material printing in the Cloud Slicer
- Multi-material printing in SimplyPrint: mapping and syncing your AMS, ACE or CFS
Updated on: 27/10/2026
Thank you!